All Categories

Blogs

 >  News >  Blogs

Cable Gland Thread Types: M-Metric vs. NPT vs. PG — The Complete B2B Specification Guide

Nov 02, 2026

Three thread standards compared: M-metric (top row), NPT tapered thread (middle row), and PG thread fittings (bottom row) with gauges for reference.

Three thread standards compared: M-metric (top row), NPT tapered thread (middle row), and PG thread fittings (bottom row) with gauges for reference.

Introduction: Thread Mismatch Is the #1 Cause of Cable Gland Site Returns

In over 18 years of supplying cable glands to B2B customers across Europe, the Middle East, and Asia-Pacific, the single most common cause of site returns and project delays is thread mismatch: the gland ordered has a different thread standard from the enclosure knockout. A gland with M20 metric thread cannot be installed in a ½" NPT knockout — and forced installation strips threads, destroys IP ratings, and creates safety hazards.

This guide gives procurement engineers, project managers, and site supervisors the reference they need to specify the correct thread standard every time — covering the three dominant global standards (M-metric, NPT, PG), their dimensional equivalents, the regions and industries where each dominates, and the adapter solutions available when a mismatch is unavoidable.

 

Section 1 — The Three Global Thread Standards

M-Metric (ISO 965): The Global Default

M-metric threads, defined by ISO 965, are the international standard for cable glands used in European-design equipment and the most widely specified thread standard globally. The designation is straightforward: M20 means 20mm nominal outer diameter with a standard 1.5mm pitch. M-metric threads are parallel (cylindrical) — the IP sealing is provided by the gland sealing ring or a separate O-ring at the enclosure face, not by the thread engagement itself.

Metric Size

Cable OD Range (typical)

Equivalent PG (approx.)

Application

M12 × 1.5

3–6.5 mm

PG7

Instrument cables, sensors

M16 × 1.5

4–8 mm

PG9

Control cables, small signal

M20 × 1.5

6–12 mm

PG11/PG13.5

Standard power cable (2.5–10mm²)

M25 × 1.5

10–17 mm

PG16

Medium power cable

M32 × 1.5

15–21 mm

PG21

Multi-core, larger cable

M40 × 1.5

19–28 mm

PG29

Large power cable, armored

M50 × 1.5

25–35 mm

PG36

High-power armored cable

M63 × 1.5

34–44 mm

PG48

Large armored HV cable

 

NPT (ANSI/ASME B1.20.1): The North American Standard

National Pipe Thread (NPT) is the mandatory standard for cable glands used in North American electrical equipment and UL-listed panel enclosures. NPT is a tapered thread — the thread OD increases from the tip toward the body, creating a wedging seal as the gland is tightened. This means NPT provides thread-entry sealing without a separate O-ring, but it also means NPT glands must not be over-tightened (which can crack the enclosure boss).

  • ½" NPT → equivalent to approx. M20 metric cable OD range
  • ¾" NPT → equivalent to approx. M25 metric cable OD range
  • 1" NPT → equivalent to approx. M32 metric cable OD range
  • Regional use: USA, Canada, Mexico, some Middle Eastern projects with US engineering specifications

PG Thread (DIN 40430): The European Legacy Standard

PG (Panzergewinde, or armored conduit thread) is a German-origin standard that was dominant in European electrical equipment through the 1990s. It is now technically superseded by M-metric under IEC standards, but vast quantities of PG-threaded enclosures remain in service and continue to be specified for replacement parts and retrofit projects. PG thread is parallel like M-metric.

  • PG11 → closest metric equivalent M20
  • PG13.5 → closest metric equivalent M20 (larger cable range)
  • PG16 → closest metric equivalent M25
  • PG21 → closest metric equivalent M32
  • Note: PG and M-metric are not interchangeable — a M20 gland will not thread into a PG16 knockout even though the cable OD ranges overlap

 

Installing three different thread standards: M20 metric (left), ½

Section 2 — Thread Standard by Region

Region

Primary Standard

Legacy Standard

Notes

Europe (EU)

M-metric (ISO 965)

PG (DIN 40430)

PG still common in retrofit work

North America

NPT (ANSI B1.20.1)

None

UL/NEC mandatory for listed equipment

China (domestic)

M-metric

None

Export follows buyer standard

Middle East

M-metric or NPT

None

Depends on engineering origin (EU vs US EPC)

Southeast Asia

M-metric

PG (older equipment)

Growing standardization on M-metric

Australia/NZ

M-metric

None

AS/NZS 61439 aligned with IEC

Latin America

NPT or M-metric

None

US-EPC projects use NPT; EU-EPC use M-metric

 

Section 3 — Conversion Adapters: When You Cannot Avoid Mismatch

When retrofit projects require connecting M-metric glands to PG-threaded enclosures (or NPT to M-metric), adapter bushings provide a valid solution — but they must be specified carefully:

  • M20 to PG16 adapter: Allows M20 metric gland in PG16 knockout. Check that adapter OD clears the panel interior and does not interfere with cable routing.
  • NPT to M-metric adapter: ½" NPT female to M20 male allows metric gland in NPT enclosure. Seal the NPT thread with PTFE tape — do not rely on thread engagement alone for IP rating.
  • IP rating impact: Any adapter introduces an additional sealing interface. Always verify the assembly IP rating with a submersion test rather than assuming rated IP passes through the adapter.

 

Section 4 — Hoonsun Thread Standard Availability

  • M-metric: M12 to M63, 1.5mm pitch standard, 2mm pitch available — full size range in stock
  • PG thread: PG7, PG9, PG11, PG13.5, PG16, PG21, PG29, PG36, PG42, PG48 — in-stock for European retrofit supply
  • NPT: ⅜", ½", ¾", 1", 1¼", 1½", 2" — UL Listed grades available for North American market
  • BSP (G thread, ISO 228): G¼ to G2 parallel thread — for UK-market equipment and instrumentation

Mixed-standard orders: RFQ specifying multiple thread standards for one project accepted — single shipment consolidation available

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Copyright © Zhejiang Hongxiang Connector Co., Ltd. All Rights Reserved  -  Privacy Policy